How Much Does an Electric Fireplace Cost to Install? (2026)

What an electric fireplace costs to install in 2026: published ranges by type, what the electrical side adds (plug, hardwire, new circuit), and how to keep the cost down in West Texas.

Share:

Residential Breaker Panel with Two Rows of Circuit Breakers and a Handwritten Circuit Directory on the Door

Summary:

Published cost guides put most electric fireplace installations at about $200 to $2,200, with an average near $1,000, per HomeAdvisor and Angi. Fixr puts the typical job at $540 to $1,005, and a built-in or custom unit can run $2,000 to $10,000 or more. The electrical side is the swing factor: a plug-in unit may need nothing new, while a hardwired insert or a unit that needs its own circuit adds electrician time, and a new dedicated circuit is priced at about $250 to $1,000 in published guides. These are national ranges for budgeting, not a quote.

Table of contents

An electric fireplace is one of the simpler heating projects in a house. There is no chimney, no gas line and no venting. What decides the price is the type of unit you pick and how it gets power: a freestanding model that plugs into the wall, a wall-mounted or recessed unit that may be hardwired, or an insert that goes into an old firebox. This guide lays out the published price ranges for each, and explains the electrical work that sits behind them.

Hooked Up Electric is a licensed Texas electrical contractor with offices in Abilene, San Angelo, Midland, and Lubbock. We handle the electrical side of fireplace projects: checking the circuit, adding a dedicated circuit or outlet when the unit needs one, and hardwiring units that are built to be wired in.

Electric Fireplace Installation Cost at a Glance (2026)

These are the published national ranges from the cost guides we read for this article.

ItemPublished rangeSource
Typical total, most homeowners$200 to $2,200 (average about $1,000)HomeAdvisor; Angi
Typical installation job$540 to $1,005 (average $750)Fixr
Freestanding unit, installed$200 to $500HomeAdvisor
Wall-mounted unit, installed$300 to $2,000 (HomeAdvisor); $500 to $2,500 or more (HomeGuide)HomeAdvisor; HomeGuide
Fireplace insert$400 to $2,000 (HomeAdvisor); $200 to $2,000 (HomeGuide)HomeAdvisor; HomeGuide
Built-in (recessed) unit$1,500 to $3,000 or moreHomeGuide
Custom built-in installation$2,000 to $10,000Fixr
Electrician labor$50 to $100 per hour (HomeAdvisor); $52 to $97 per hour (Fixr)HomeAdvisor; Fixr
Hardwiring the unitAbout $200 (HomeAdvisor); about $150 in labor for a job of about 1.5 hours (Fixr)HomeAdvisor; Fixr
New dedicated circuit$250 to $900 (HomeGuide); $570 to $1,000, average about $700 (Angi)HomeGuide; Angi
Electrical permit$50 to $350HomeGuide

Why the ranges differ. Each guide groups the job differently. Some quote the unit and installation together, some quote the unit alone, and some quote only the labor. HomeGuide prices freestanding units at $200 to $1,500 for the unit alone, because most need no installation at all. The biggest jumps come from two things: a built-in unit that needs a framed wall or surround, and a new circuit run from the panel when the existing outlet cannot carry the heater.

Plug-In, Hardwired, or Built-In: Which Type You Have Matters

The type of fireplace sets most of the labor:

  • Freestanding and mantel units plug into a standard outlet. Angi lists installation for a plug-in freestanding or tabletop unit at $0, since you set it in place and plug it in.
  • Wall-mounted units hang on the wall like a TV. HomeGuide notes they can be hardwired or plugged in, so the cost depends on whether there is a usable outlet where the unit goes.
  • Inserts slide into an existing wood or gas firebox. Angi says inserts must be hardwired, and you will need an electrician if the installer does not do the wiring. If the firebox was gas, HomeAdvisor lists capping the gas line at about $130 on average.
  • Built-in (recessed) units sit inside the wall. HomeGuide says they need more labor and may need framing, and Fixr puts custom built-in work at $2,000 to $10,000.

Read the installation manual before you buy. It will say whether the unit ships with a cord, whether it can be hardwired, and what circuit it expects. For example, the manual for one 120 volt linear model (Modern Flames Spectrum Slim) lists a maximum draw of 1,465 watts and calls for a dedicated 15 amp or larger breaker. The manual for a Dimplex built-in model (BFSL33) says it is factory set for 208/240 volt operation, can be switched to 120 volts, and needs a dedicated 15 amp circuit with 12 gauge wire when the heater is used.

The Electrical Part of the Job: Outlet, Circuit, or Hardwire

The heater is what makes an electric fireplace an electrical project. Angi notes that many models have 750 watt and 1,500 watt settings, about the same as a space heater of similar size. On a 120 volt circuit, a heater near that top setting uses a large share of what a standard 15 amp circuit can carry, which is why manufacturers ask for a circuit of its own.

There are three common outcomes when an electrician looks at the spot you picked:

  1. The existing outlet works. If the outlet is on a circuit with little else on it and the manual allows a plug-in connection, there may be no electrical cost.
  2. A new outlet or circuit is needed. HomeGuide lists electric fireplaces among the appliances that may need a dedicated circuit, and prices a new dedicated circuit at $250 to $900, with most homeowners paying about $650. Angi’s range is $570 to $1,000. Our electrical outlet installation cost guide covers outlet work in more detail.
  3. The unit is hardwired. Inserts and many built-in units connect to a junction box instead of a plug. HomeAdvisor lists hardwiring by an electrician at about $200, and Fixr describes it as a job of about 1.5 hours.

A 240 volt unit needs a 240 volt circuit, which is a different job from a standard outlet. Our 240V outlet cost guide explains that work. If the panel has no open spaces for a new breaker, see our breaker replacement cost guide and talk to the electrician about options before you buy the unit.

Safety and Code: What the Manuals and Fire Officials Say

An electric fireplace with a heater should be treated like any other heating appliance. A few rules come up again and again:

  • No extension cords or power strips. The U.S. Fire Administration says to plug space heaters directly into wall outlets and never into an extension cord or power strip. The Spectrum Slim manual says the same for that fireplace, and adds that no other appliances should be plugged into the same circuit.
  • Follow the manual’s circuit size. Both manuals we read call for a dedicated 15 amp circuit for heat operation. A unit that shares a circuit with a TV, lamps and a vacuum is more likely to trip the breaker.
  • Wiring to code. The Dimplex manual says installation must comply with local and national electrical codes and utility requirements. The Spectrum Slim manual says a qualified electrician must do the work if the cord is removed and the unit is wired directly to the house wiring.
  • Licensed work in Texas. The Texas Department of Licensing and Regulation states that anyone who performs electrical work in Texas must be licensed, with listed exemptions. Running a new circuit or hardwiring a unit is electrical work.
  • Clearances. HomeGuide notes that installers need to keep the unit clear of combustible materials. The manual gives the exact clearances for each model.

Check with your city before the work starts. HomeGuide lists electrical permit costs of $50 to $350, and some cities include the inspection in the permit fee.

What Changes the Price in West Texas

The national ranges above hold in West Texas, but a few local factors push a job up or down:

  • Distance from the panel. A new circuit costs more the farther it runs. A living room wall far from a garage panel takes more wire and more time.
  • Wall type and finish. Brick, stone and finished walls take longer to fish wire through or open up. Angi notes that finished walls needing repair can drive up the cost of outlet work.
  • Older homes and panels. In some older houses the panel is already full or close to its limit. If there is no room for a new breaker, that has to be solved first. Our panel upgrade cost guide covers that decision.
  • Converting an old fireplace. Putting an insert into a gas firebox adds gas line capping, and an older masonry fireplace may need an outlet run to the firebox.
  • Built-in work. Framing, drywall, tile and a mantel are separate trades and can add more than the electrical work itself.

How to Keep the Cost Down

  1. Read the manual before you buy. Know whether the unit plugs in or hardwires, and what circuit it needs, so there are no surprises on install day.
  2. Pick a spot with power nearby. A location near an outlet on a lightly used circuit, or near the panel, keeps wiring short.
  3. Bundle electrical jobs. If you also need a TV outlet, a new switch or a ceiling fan, have the electrician do it on the same visit. HomeGuide notes that many electricians charge a call-out fee of $100 to $200 that covers the first hour.
  4. Match the unit to the room. HomeGuide’s rule of thumb is about 20 BTUs per square foot. A unit sized for the room avoids paying for heat output and circuit capacity you do not need.
  5. Get the framing done first. For a built-in, have the opening framed with the electrical box in place before drywall goes up. Opening a finished wall later costs more.
  6. Ask for a written scope. A clear quote that lists the circuit, breaker, outlet or junction box, and permit makes it easy to compare electricians. Our electrician cost guide explains how electricians price their time.

Frequently Asked Questions About Electric Fireplace Installation Costs

How much does it cost to install an electric fireplace?

HomeAdvisor and Angi put most electric fireplace projects at about $200 to $2,200, with an average near $1,000. Fixr lists a typical installation at $540 to $1,005. Built-in and custom units cost more.

Do I need an electrician to install an electric fireplace?

Not always. A freestanding unit that plugs into a suitable outlet needs no electrician. Hardwired units, inserts, and any job that needs a new outlet or circuit should be done by a licensed electrician; in Texas, electrical work requires a license unless an exemption applies.

Does an electric fireplace need a dedicated circuit?

Many do when the heater is used. The two manuals we read, from Modern Flames and Dimplex, both call for a dedicated 15 amp circuit for heat operation. Check the manual for your model.

Can I plug an electric fireplace into an extension cord or power strip?

No. The U.S. Fire Administration says to plug space heaters directly into a wall outlet and never into an extension cord or power strip, and fireplace manuals give the same warning.

How much does it cost to add a circuit for an electric fireplace?

HomeGuide prices a new dedicated circuit at $250 to $900, with most homeowners paying about $650. Angi lists $570 to $1,000, with an average of about $700. Distance from the panel and wall type move the price.

How much does an electric fireplace cost to run?

Angi estimates about $1.85 of electricity for eight hours of use. Your cost depends on your electricity rate and how often the heater runs.

Planning an electric fireplace? Call Hooked Up Electric at 325-442-5594 or request a quote online. We serve Abilene, San Angelo, Midland, and Lubbock.

Sources: HomeAdvisor, electric fireplace cost guide (undated); Angi, electric fireplace cost guide (2025 data) and dedicated circuit cost guide (2026 data); HomeGuide, electric fireplace cost guide (undated) and dedicated circuit cost guide (undated); Fixr, electric fireplace installation cost (updated January 2025); Modern Flames, Spectrum Slim owner’s manual (undated); Dimplex, BFSL33 installation manual (2016); U.S. Fire Administration, space heater safety pictograph (undated); Texas Department of Licensing and Regulation, Electricians FAQ (undated).

author avatar
seoeditor123

Article details:

Share: