How Much Does Outdoor Lighting Cost to Install? (2026)

What outdoor lighting costs to install in West Texas in 2026: published prices per fixture and per project, low voltage versus 120 volt, trenching, transformers, and what adds to the bill.

Share:

a Wall Mounted Outdoor Light with a Small Solar Panel Glowing Bright White on a Light Colored Exterior Wall at Night Next to a Dark Window

Summary:

Published 2026 cost guides put a professionally installed outdoor lighting project at about $2,000 to $6,000, with a $4,000 average (Angi and HomeAdvisor), and individual fixtures at roughly $50 to $500 each installed. A single replacement fixture on existing wiring runs about $65 to $175 (Angi), while a low voltage landscape light is about $100 to $150 per fixture installed (Angi, HomeGuide). The biggest swing comes from how much new wiring and trenching the job needs. These are national ranges for budgeting, not a quote.

Table of contents

Outdoor lighting covers a lot of ground: a new porch light, floodlights over the driveway, path lights along a walk, or a full landscape system on a timer. Because the jobs are so different, a single “average price” does not tell you much. This guide breaks the published 2026 prices down by fixture, by power source and by the electrical work behind them, so you can see where your project is likely to land.

Every number below comes from a named cost guide or agency page read for this article, listed at the end. Hooked Up Electric is a licensed Texas electrical contractor with offices in Abilene, San Angelo, Midland, and Lubbock. We do the 120 volt side of outdoor lighting: new circuits, outdoor boxes, switches, timers and the power feed for landscape transformers.

Outdoor Lighting Installation Cost at a Glance (2026)

Here is what the major national cost guides report for outdoor lighting in 2026, installed prices unless noted.

ItemPublished rangeSource
Typical professional project$2,000 to $6,000 ($4,000 average)Angi
Landscape lighting project range$1,000 to $7,500 ($4,000 average)HomeAdvisor
Landscape lighting, 10 to 20 lights$800 to $6,000HomeGuide
Per fixture, installed$80 to $300HomeGuide
Replace an existing exterior fixture$65 to $175 eachAngi
Low voltage landscape light$100 to $150 each ($125 average)Angi
Pathway light$50 to $150 eachHomeAdvisor, HomeGuide
Porch light$75 to $250 each ($150 average)Angi
Floodlight$75 to $250 each ($150 average)Angi
Motion sensor security light$350 to $500 each ($425 average)Angi
Lamp post$400 to $1,000HomeAdvisor
Transformer for low voltage, installed$200 to $500HomeGuide
Adding hardwiring where none exists$300 to $500Fixr
Trenching$4 to $12 per linear footAngi
Electrician labor$50 to $100 per hourAngi, HomeAdvisor

Why the ranges differ. The guides price different things. Angi and HomeAdvisor quote whole projects, which often include design, several fixture types and buried cable. HomeGuide quotes per fixture and by the number of lights. Fixr, last updated in January 2025, puts its national average lower at $3,000, with most projects between $2,000 and $4,000 and a low end of about $300 for a front and back porch light. The common thread: the fixture is often the smaller part of the bill, and the wiring needed to reach it is the larger part.

Low Voltage, 120 Volt, or Solar: Which Kind of Light?

Outdoor lights fall into three groups, and each one has a different installation cost.

  • Low voltage (12 volt) landscape lighting. Path lights, uplights and spotlights run off a transformer that plugs into or is wired to a 120 volt supply. Angi puts these at $100 to $150 per fixture installed, and HomeAdvisor at $90 to $150. HomeGuide lists the transformer at $200 to $500 installed. Angi notes you need an electrician to install the 12 volt transformer.
  • 120 volt (line voltage) fixtures. Porch lights, wall packs, floodlights and lamp posts are wired directly to a household circuit. Replacing one on existing wiring is the cheapest outdoor job: Angi lists $65 to $175 per fixture. A brand new location that needs a new run of cable is a different job, and Fixr puts the added hardwiring at $300 to $500.
  • Solar and battery lights. Fixr lists solar lights at $100 to $200 installed and battery lights at $100 to $300, because no wiring has to reach them. The tradeoff is output and reliability: they depend on the panel getting sun and on the battery holding a charge.

Many homes end up with a mix: hardwired lights on the house and garage, and low voltage lights in the beds and along the walk. Fixr makes the same point, noting that hardwired lights suit porch and garage lighting attached to the house.

The Main Cost Driver: Getting Power to the Light

On most outdoor jobs, the wire costs more than the light. Three things decide how much wiring you are paying for.

Distance from the panel or nearest circuit. Angi lists wiring an outdoor fixture at $2 to $4 per linear foot. Lights mounted on the house close to an existing circuit are quick. A lamp post at the end of a driveway is not: HomeGuide puts an underground line to a lamp post at $10 to $25 per linear foot.

Trenching. Buried cable has to go in a trench. Angi lists trench digging at $4 to $12 per linear foot, HomeGuide at $5 to $12, and HomeAdvisor lists trenching with new underground wiring at $3 to $5. HomeGuide notes the price depends on trench size and soil type, so hard or rocky ground costs more to dig.

Whether the panel needs anything. A large lighting load may need its own circuit. HomeGuide lists a new circuit breaker at $150 to $300 installed and a new GFCI outlet at $150 to $350. If you are planning several outdoor outlets as well, our electrical outlet installation cost guide and GFCI outlet cost guide cover those prices.

Who Can Install Outdoor Lighting, and Do You Need a Permit?

In Texas, electrical work that is not exempt has to be done by a licensed electrician working through a licensed electrical contractor, according to the Texas Department of Licensing and Regulation. Fixr gives the same advice in plain terms: electrical work needs a licensed contractor, and it recommends against doing it yourself.

Permits depend on the city and the scope of the job. HomeGuide says permits are usually only needed when wiring is added or updated, and Fixr says replacing a fixture on existing wiring generally does not need one while new wiring usually does. Before you start, ask your installer whether your city requires a permit for the specific work you are planning.

Outdoor lighting also connects to safety and security. If your main goal is to light up dark corners, driveways and entry points, our security lighting cost guide goes deeper on motion sensor lights and floodlights.

What Changes the Price in West Texas

The national ranges above are a starting point. Several things specific to the home and the property move the final number.

  • How far the lights are from power. Ranch style homes on large lots and long driveways mean longer cable runs and more trenching, priced by the foot.
  • The ground you are digging in. HomeGuide notes that trenching cost depends on soil type. Hard or rocky ground takes longer to trench than loose soil.
  • Mounting height and access. Floodlights under a high eave or on a detached shop need a taller ladder or lift and more time.
  • Fixture choice. Fixr lists installed prices by material from $75 to $300 for plastic up to $125 to $500 for brass. Lamp posts and bollards sit at the top of the per fixture range.
  • Controls. Photocells, motion sensors and timers add parts and wiring, but they also cut running time.
  • Combining jobs. Adding an outdoor outlet, a new circuit or a fixture swap inside the house on the same visit spreads the trip and setup cost over more work.

How to Keep the Cost Down

  1. Start where power already exists. Replacing or upgrading fixtures on existing outdoor boxes is the cheapest work on the list, at about $65 to $175 per fixture (Angi).
  2. Use low voltage for beds and paths. One transformer can feed many small lights, and low voltage cable is easier to run than a buried 120 volt circuit.
  3. Plan the layout once. Group lights so one trench or one cable run serves several of them, instead of separate runs to each spot.
  4. Choose LED. Fixr lists the yearly running cost of an LED bulb at $1.19, compared with $5.05 for halogen, and HomeGuide puts a landscape system at about $20 to $60 a year in electricity.
  5. Add smart controls. The U.S. Department of Energy says photosensors are useful for all types of outdoor lighting and suggests pairing motion sensors with photosensors on security lights, so they run only when it is dark and someone is there.
  6. Bundle the electrical work. If you also need an outdoor GFCI outlet or a circuit for a shop light, do it on the same visit.

Frequently Asked Questions About Outdoor Lighting Installation Costs

How much does it cost to install outdoor lighting?

Published 2026 guides put a typical professional outdoor lighting project at $2,000 to $6,000, with an average of about $4,000 (Angi). HomeAdvisor reports a wider $1,000 to $7,500 range for landscape lighting, also averaging $4,000. Small jobs, such as replacing one exterior fixture on existing wiring, run about $65 to $175 (Angi).

How much does low voltage landscape lighting cost per fixture?

Angi and HomeGuide both list low voltage landscape lights at $100 to $150 per fixture installed, and HomeAdvisor at $90 to $150. The transformer that powers the system costs $200 to $500 installed, according to HomeGuide.

How much does it cost to run power to an outdoor light?

Angi lists wiring an outdoor fixture at $2 to $4 per linear foot and trenching at $4 to $12 per linear foot. Fixr puts adding hardwiring where none exists at $300 to $500. For a lamp post, HomeGuide lists an underground line at $10 to $25 per linear foot.

Do I need an electrician to install outdoor lights?

For hardwired 120 volt lights, yes. In Texas, electrical work that is not exempt must be done by a licensed electrician through a licensed electrical contractor (TDLR). Angi also notes that a low voltage system needs an electrician to install the 12 volt transformer.

Do I need a permit for outdoor lighting?

It depends on your city and the job. HomeGuide says permits are usually only needed when wiring is added or updated, and Fixr says replacing a fixture on existing wiring generally does not need one, while new wiring usually does.

Are solar outdoor lights cheaper than hardwired lights?

Installed, they cost about the same per light: Fixr lists both solar and hardwired lights at $100 to $200. The difference is that a new hardwired location may also need $300 to $500 in added wiring (Fixr), which solar lights avoid. Solar lights depend on sun and battery condition.

Planning new outdoor lights or more power to the yard? Call Hooked Up Electric at 325-442-5594 or request a free quote. You can also read more about our lighting installation services, browse outdoor lighting ideas for Texas homes, or find your nearest office in Abilene, San Angelo, Midland, or Lubbock.

Sources: Angi, Electrician Cost to Install Outdoor Light (updated October 2026); HomeAdvisor, What Does Landscape Lighting Cost to Install? (updated June 2026); HomeGuide, How Much Does Landscape Lighting Cost? (2026 prices); Fixr, Outdoor Light Installation Cost (updated January 2025); U.S. Department of Energy, Energy Saver, Lighting Controls; Texas Department of Licensing and Regulation, Electricians program page.

author avatar
seoeditor123

Article details:

Share: