Summary:
Published 2026 cost guides put smoke detector installation at about $70 to $150 per alarm. HomeAdvisor’s average is $115 and Fixr’s is $112 for a dual-sensor hardwired alarm, installed. Replacing a hardwired alarm on wiring that is already there sits at the low end. Adding hardwired, interconnected alarms where there is no wiring costs more: HomeAdvisor says a single hardwired unit could reach $500 or more in that case. These are national ranges for budgeting, not a quote. How many alarms you need, how easy the attic is to reach, and whether the alarms must be interconnected decide where your job lands.
A smoke alarm is the cheapest piece of safety equipment in a house, and it only works if it has power. NFPA’s research on home fires found that almost three out of five home fire deaths happened in homes with no smoke alarms or with alarms that did not work, and that the risk of dying in a reported home fire is 54% lower in homes with working smoke alarms. Most failures come down to the power source: missing, disconnected, or dead batteries.
This guide lays out what the major national cost guides say smoke detector installation costs in 2026, what separates a $70 swap from a whole house of new hardwired alarms, and where the code expects alarms to go. Hooked Up Electric is a licensed Texas electrical contractor with offices in Abilene, San Angelo, Midland, and Lubbock. The prices below are published ranges to help you budget. For a real number, call and tell us how many alarms you have and whether they are battery or hardwired.
Smoke Detector Installation Cost at a Glance (2026)
Typical prices from published national cost guides. Installed prices include the alarm unless stated.
| Item | Published range | Source |
|---|---|---|
| Typical installation, per alarm | $70 to $150 (average $115) | HomeAdvisor |
| Typical installation, per alarm | $70 to $150 (average $112 for a dual-sensor hardwired alarm) | Fixr |
| Professional installation, per alarm, depending on type | $110 to $400 | Angi |
| Hardwired unit where no wiring exists | can reach $500 or more | HomeAdvisor |
| Three hardwired alarms with a new base (high end example) | up to $398 | Fixr |
| Electrician hourly rate | $50 to $100 per hour | HomeAdvisor |
| Electrician time per hardwired alarm | about 1 hour | Fixr |
| Battery-only alarm (unit only) | $5 to $50 | HomeAdvisor |
| Hardwired alarm (unit only) | $15 to $80 | HomeAdvisor |
| Photoelectric alarm (unit only) | $30 to $80 | Fixr |
| Smart features (added to the alarm price) | $50 to $150 or more | HomeAdvisor |
| How long an alarm lasts | 10 years, then replace the whole unit | HomeAdvisor, Fixr, American Red Cross |
Why the ranges differ: swapping an old hardwired alarm for a new one uses the box, the wiring, and the interconnect wire that are already in the ceiling, so the job is mostly the alarm and a short visit. Adding alarms where there was nothing means a cable run through the attic to each location, a box at each alarm, and an interconnect so every alarm sounds together. Angi’s wider $110 to $400 range reflects that spread; it also notes that most homeowners spend $70 to $150 depending on the detector type. Electricians often lower the price per alarm when there are several on one visit, Fixr says, so replacing all of them at once usually costs less per alarm than one at a time.
Battery, Hardwired, or Smart: What Each Costs
- Battery-only alarms are the cheapest to buy ($5 to $50 per HomeAdvisor, $10 to $35 per Fixr) and you can mount them yourself. The catch is the battery: NFPA found that alarms that fail usually fail because the power source was missing, disconnected, or dead.
- Hardwired alarms run on the house wiring with a battery backup. The unit costs $15 to $80 (HomeAdvisor) or $30 to $50 (Fixr). Fixr says replacing a hardwired alarm requires an electrician, since it involves connecting wires. Hardwired alarms are usually interconnected: when one sounds, they all sound.
- Smart alarms add phone alerts and app control. HomeAdvisor says smart features add $50 to $150 or more, and Fixr puts smart alarms at $80 to $180 per unit, and some come with a monitoring fee.
- Sensor type. Fixr lists ionization alarms at $10 to $25 and photoelectric alarms at $30 to $80; dual-sensor alarms combine both. The sensor type changes the unit price more than the installation price.
If your home already has hardwired alarms, replace them with hardwired alarms. Swapping a hardwired alarm for a battery unit and capping the wires removes the interconnect and the house power the alarm was designed around.
Replacing Hardwired Alarms vs. Adding Them Where There Is No Wiring
Replacing existing hardwired alarms is the common job. Alarms last about 10 years, so in many homes the whole set reaches the end of its life at the same time. The electrician turns off the circuit, removes each old alarm, fits the new mounting plate and plug, and tests the interconnect so a test at one alarm sets off the rest.
Adding hardwired alarms where there are none is a wiring job. Each new location needs a ceiling box and a cable back to the circuit, and the alarms need an interconnect so they sound together. Attic access matters a lot here: an open attic over a single story house is the easy case, and a finished second floor or a low roof pitch adds time. HomeAdvisor says that without existing wiring, a single hardwired unit can reach $500 or more.
A remodel can trigger the second job. The International Residential Code says that when alterations, repairs, or additions requiring a permit are made, or a bedroom is added, the home must be fitted with smoke alarms located as required for new homes. The code also has exceptions: alarms added this way may be allowed on battery power, and interconnection may not be required when the walls and ceilings are not opened up. Your city’s building department decides which edition of the code applies and how it is enforced, so ask when you pull the permit.
Where Smoke Alarms Are Required
The International Residential Code, section R314, sets these rules for homes it covers:
- Locations: in each sleeping room, outside each separate sleeping area in the immediate vicinity of the bedrooms, and on each additional story, including basements and habitable attics.
- Interconnection: where more than one alarm is required, the alarms are interconnected so that one alarm going off sets off all of them.
- Power: alarms get their primary power from the building wiring, with a battery for when that power is out.
For existing homes that have no alarms, the American Red Cross says to install them at a minimum on every level and outside each sleeping area, and recommends interconnected alarms in each bedroom and throughout the home for the best protection. It also says to test alarms at least monthly with the test button, replace batteries in battery-powered alarms at least once a year, and replace the alarms every 10 years.
Placement details matter too. Fixr notes that ceiling mounting is preferred, ceiling alarms should sit more than 4 inches from a wall, wall-mounted alarms should be no more than 12 inches below the ceiling, and alarms should stay away from windows, doors, and air ducts.
Texas Rules for Rental Homes
If you own a rental, Texas law sets a minimum. Texas Property Code section 92.255 requires a landlord to install at least one smoke alarm in each separate bedroom, at least one in the hallway near the bedrooms when several bedrooms share a corridor, and at least one on each level of a multi-level unit. For units first occupied before September 1, 2011, the alarms may be battery powered and do not have to be interconnected; replacements in those units must meet the building code standards that applied to the unit. For anything beyond that, read the current statute or ask a Texas attorney. We can install and test the alarms; we cannot give legal advice.
If you have several units, scheduling all the replacements for one visit keeps the per alarm labor down.
How to Keep the Cost Down
- Replace them all at once. Alarms installed together age together, and several alarms on one visit cost less per alarm than separate trips.
- Count your alarms and note the brand and model before you call, so the right replacements come on the first trip.
- Clear the path to the attic if new wiring is needed. Time spent moving storage is time on the bill.
- Bundle other small jobs. If you also need an outlet, a light, or a GFCI, one visit is cheaper than three. Our electrician cost guide explains how service calls are priced.
- Pick the features you will use. A standard hardwired alarm with battery backup protects you; smart features are a convenience, not a requirement.
- Get the quote in writing with the number of alarms, the unit price, any new wiring, and any permit listed separately.
Frequently Asked Questions About Smoke Detector Installation Costs
How much does it cost to install a smoke detector?
HomeAdvisor and Fixr both put the typical range at $70 to $150 per alarm, with averages of $115 and $112. Angi gives a wider $110 to $400 per unit for professional installation depending on the type, and HomeAdvisor says a hardwired unit where no wiring exists can reach $500 or more.
How much does an electrician charge to install a hardwired smoke detector?
HomeAdvisor puts electrician rates at $50 to $100 per hour for the hookup, and Fixr says a hardwired alarm takes about an hour. Several alarms on one visit usually cost less per alarm than one at a time.
Can I replace a hardwired smoke detector myself?
Fixr says replacing a hardwired alarm requires an electrician, since it involves connecting wires to the house circuit. Battery-only alarms can be mounted by the homeowner.
How often should smoke detectors be replaced?
Every 10 years, according to the American Red Cross, HomeAdvisor, and Fixr. The Red Cross also says to test alarms at least monthly and to replace the batteries in battery-powered alarms at least once a year.
Where are smoke detectors required?
The International Residential Code, section R314, calls for alarms in each sleeping room, outside each separate sleeping area near the bedrooms, and on each additional story, interconnected and powered by the house wiring with battery backup. Your city decides which edition applies.
Do Texas landlords have to provide smoke alarms?
Yes. Texas Property Code section 92.255 requires at least one smoke alarm in each separate bedroom, one in the hallway near the bedrooms when they share a corridor, and one on each level of a multi-level unit. Older units occupied before September 1, 2011 may use battery alarms that are not interconnected.
Ready to replace old alarms or add hardwired ones? Call 325-442-5594 or request a free quote. We work out of offices in Abilene, San Angelo, Midland, and Lubbock.
Sources: HomeAdvisor, smoke detector installation cost (updated June 2026); Angi, how to hire a smoke detector installation pro (updated May 2026); Fixr, smoke detector installation cost (updated January 2025); NFPA, Smoke Alarms in U.S. Home Fires (Marty Ahrens, January 2019); International Code Council, International Residential Code section R314; American Red Cross, fire safety equipment; Texas Property Code section 92.255.



